7.3L Ford Powerstroke High Pressure Oil System IPR Air Test Tool

7.3L Ford Powerstroke High Pressure Oil System IPR Air Test Tool
7.3L Ford Powerstroke High Pressure Oil System IPR Air Test Tool
7.3L Ford Powerstroke High Pressure Oil System IPR Air Test Tool

7.3L Ford Powerstroke High Pressure Oil System IPR Air Test Tool

7.3L Powerstroke Diesel - High Pressure Oil System IPR Air Test Fitting - Test it the right way! Each year Motor Magazine selects the Top 20 most innovative new tools in the automotive industry. We are pleased to announce that the 6.0L IPR Air Test Tool was selected to receive this highly coveted award for 2014. See the photos above for a clip of the Motor Magazine article. Due to popular demand we now offer the IPR air test fitting / tool for the 7.3L engine also.

Also Fits International T444E, DT466E, and CAT 3126. 7.3L Powerstroke engines may experience hard start and or no start issues. In some cases the no-start issue may occur only with the engine hot. If the observed ICP pressure during cranking is less than the required 500 PSI, then the problem is in the high pressure oil system.

One of the first checks that should be made is to remove the plug from the top of the high pressure oil reservoir (in front of the fuel filter) to observe if the reservoir is full. If the oil is standing within an inch of the top of the reservoir, then the problem is in the high pressure oil system and could be caused by one of three things. The high pressure oil pump itself. A high pressure oil leak.

The 7.3L IPR Air Test Tool will allow you to quickly determine which of these is the case (without unnecessary and costly parts substitution) by performing the following. Remove the IPR valve and pressurize the system with shop air. External high pressure oil leaks would have, of course, been obvious.

The primary concern is internal leaks under the valve covers. These could include leaking injector orings, or leaking injectors. Listen for any leaks under the valve covers and correct if present. If the center injector oring fails high pressure oil could be leaking back into the fuel system. Remove the fuel filter cap and observe for air bubbles in the fuel.

If necessary, individual fuel lines running from the fuel filter assembly to the cylinder heads can be disconnected in order to isolate the problem. If no air leaks are observed, the next step is to isolate whether the problem is with the IPR or the high pressure oil pump. Remove the IDM fuse or unplug the IDM or injector connectors at the valve covers to prevent starting. Close the valve on the IPR air test tool and crank the engine. This step effectively deadheads the high pressure oil pump - this is an approved procedure per Ford factory service info.

If the ICP pressure is now above 500 PSI, the problem is a bad IPR valve. If the pressure is under 500 PSI, then the problem lies with the high pressure oil pump.

Every 7.3L Tech needs this tool! T his fitting is made in the USA and and is built to last a lifetime. Each tool comes with three extra sets of o-rings.

Complete tool with IPR replacement fitting, heavy duty hose, and shutoff valve assembled (This Listing). Most professional technicians who do a lot of work on the 7.3L Powerstroke should choose this option. The ability to "air-up" the system and then trap the air pressure by closing the shutoff valve allows even the smallest leaks to be detected. The absence of any unwanted air noises from leaking air lines connected with quick connect couplings makes locating the real problem easier. The hose itself makes an easy "handle" to thread the fitting into the back of the high pressure oil pump which is in a somewhat difficult location.

This cost-saving option is intended for lower volume users such as individual truck owners. At less than the cost of one hour of diagnostic time in most areas, this tool can save your hundreds or even thousands of dollars. The complete system can be tested in under 20 minutes - in a professional repair facility this tool will pay for itself after one or two repairs. As with any air tool, you will need to add your own air line quick-connect fitting. Since there are so many various air fitting in use, it is impractical to provide this part.

Auto repair activities are hazardous. This tool is intended for usage by trained professionals. By using it you are certifying that you have the necessary skills and training to do so safely. We carry the repair parts you need. For these parts and many more. For the original 6.0L IPR Air Test Tool, please see the 6.0L Section.

If a delay occurs that is longer than would normally be considered commercially acceptable, we will attempt to contact you. Please take a moment to read it.

Local auto parts stores will not pay your travel costs to return a part either. Applications We guarantee our parts to be as described by part number, picture, and verbiage. While we do our best, vehicle applications, however, simply cannot be guaranteed.

In most cases, we do not generate application lists. It is the nature of the auto parts business that, in rare cases, a part will not be correct for a certain vehicle even though it "should" fit.

This may occur because of errors on application lists, mid-year production changes, changes to the vehicle since it was built, the fact that a car was not built for the US market, etc. If a part does not fit your vehicle, this does not mean the part is not as described.

Problems can be solved much more easily when civility is kept intact. The item "7.3L Ford Powerstroke High Pressure Oil System IPR Air Test Tool" is in sale since Sunday, December 21, 2014. This item is in the category "eBay Motors\Automotive Tools & Supplies\Diagnostic Service Tools\Other Diagnostic Service Tools". The seller is "accuratediesel" and is located in Bitely, Michigan.

This item can be shipped worldwide.
7.3L Ford Powerstroke High Pressure Oil System IPR Air Test Tool


Index  Archives  Contact Us  Privacy Policy Agreement  Terms of Use